Item # 2466
Steve Says: Wire and Splices not included. Great for anyone who needs to replace an existing system where the wire is already buried in the yard.
b.17 |
|
PetSafe Premium Deluxe In-Ground Radio Fence Without WireWaterproof Deluxe UltraLight Receiver with adjustable collar.
   
Features:
Covers up to 25 acres
Waterproof Deluxe UltraLight Receiver with adjustable collar
4 adjustable levels of correction plus Beep-Only Mode
Low Battery Indicator on Receiver Collar
Transmitter has built-in Lightning Protection
Pet-specific customized training method
Manual and Video CD Included
Will transmit up to 25 acres or 4000 feet of wire
Boundary Control Switch Settings: A= Greater than 2,400, B= up to 1,300, C= 1,300-2,400 feet
Boundary Width is 20% Warning Zone and 80% Static Correction Zone
Should be installed in a dry and protected environment
Boundary wire must be copper and must be insulated
Can easily use 14-20 gauge wire
Wire and Splices Not Included
Transmitter:
Height: 4.75" Width: 4.25" Depth: 2.10"
Flip up front cover
Light gray in color
Two red indicator lights (loop and power)
Wire break alarm
Two Boundary Wire terminals
Boundary Width Control Knob
"ABC" Boundary Control Switch
Adapter: Model number: RFA-14 (12v A/C, 830 ma)
Ground Terminal
Fuse protected, uses 250 volt 1/2 amp fuse
Receiver Collar:
Height: .75" Width: 2" Depth: .75" Weight: 1.5 oz
Uses 6-volt (RFA-67) Battery
Waterproof
Interchangeable Contact Points (Long and Short)
Concave inside surface (side facing throat)
Curved washers to match concave surface
25 second safety timeout
Has Progressive Correction and Anti-Linger programming
In Ground Fence Installation Guide and FAQ
Troubleshooting Your In-Ground Fence ("Short Loop Test"):
If you are having an issue with your containment system, such as your pet has gotten in or out of your containment area without getting a static correction, you may need to perform what is referred to as a short loop test. A short loop test helps determine whether you are having a problem with your in ground wire or with your equipment.
Begin by unplugging your containment transmitter and open the lid. Disconnect your boundary wire and your ground wire if one exists. Set your boundary control width knob to 10. There is a switch on the side of your transmitter. If it reads "A, B, C," set the switch to B. If it reads "High/Low," set the switch to High.
Cut a length of wire that is between 10 and 12 feet long and strip the wire coating off each end. Take this wire loop and connect each end to the two boundary wire terminals. Now plug your transmitter back in.
If your loop light is not lit and your transmitter starts beeping, check and make sure that the wire loop ends are snuggly within the terminals. If they are and your loop light is still on, and your transmitter is beeping, there is an issue with your transmitter.
If the loop light is on and your transmitter isn't beeping, your transmitter is working fine, and you should test the receiver collar as follows.
Loosen the collar probes. Attach each end of the wire on the included Collar Test Light to one of the probes underneath the exposed piece. Go to your transmitter and your short wire loop. You may have to get as close as six inches to the transmitter and wire to test the receiver collar.
When you are testing, the receiver collar should beep and your light should illuminate. If it works, your receiver is functioning properly.
If it doesn't, check your battery in your receiver collar. Make sure it is fresh and properly installed.
If the battery is fresh and installed correctly, and the test still doesn't work, it means there is something wrong with your receiver collar.
If your transmitter and your receiver collar both test okay on the short loop test, but you are still having an issue (such as your receiver collar not activating whenever it gets near the boundary wire), you may have another issue such as a wire break. At this point you should walk the containment area boundary and make sure that there isn't any activity that has disturbed your wire, such as digging or trenching. You should also check any area where you have spliced wire within your wire layout. Wire breaks tend to happen at splices, so check them and make sure no water damage or corrosion has occurred. If it has, redo your splices.
Petsafe
729849109384
MIG00-10939 |
|
GUN DOG SUPPLY - "Serving Hunting & Field Dog Owners Nationally Since 1972."
Order online via Secure Server or call 1-800-624-6378 to order! GDS Warehouse, 312 Industrial Park Road, Starkville, Mississippi, 39759 USA.
See us on the Facebook | Gun Dog Supply on LinkedIn
All words & pictures are copyright © 1997-2013, Gun Dog Supply or their respective owners. All rights reserved. Buy online with confidence when you order discount retriever hunting dog supplies, canine training equipment, k-9 accessories, and training products for your gun dog, bird dog, or working retriever. Your on-line purchase is protected through secure server ordering. Review our 100% satisfaction guarantee. Shop our canine closeout items, best bargains, k9 discount prices, good deals, cheap stuff and other values for sale. Compare our products in reviews, reports, comparisons, and buyers guides.
|
|
|
|
